- #Cisco ios xe fuji 16.7.1 installation install#
- #Cisco ios xe fuji 16.7.1 installation upgrade#
- #Cisco ios xe fuji 16.7.1 installation software#
On Cisco Catalyst 9500 Series Switches – High Performance (C9500-24Y4C, C9500-32C, C9500-32QC, and C9500-48Y4C), ISSU with Cisco StackWise Virtual is supported only starting from Cisco IOS XE Gibraltar 16.12.1.
![cisco ios xe fuji 16.7.1 installation cisco ios xe fuji 16.7.1 installation](https://www.cisco.com/c/dam/en/us/td/i/300001-400000/360001-370000/367001-368000/367274.jpg)
![cisco ios xe fuji 16.7.1 installation cisco ios xe fuji 16.7.1 installation](https://www.cisco.com/c/dam/en/us/td/i/300001-400000/350001-360000/356001-357000/356072.jpg)
On Cisco Catalyst 9500 Series Switches (C9500-12Q, C9500-16X, C9500-24Q, C9500-40X), ISSU from Cisco IOS XE Fuji 16.9.x to Cisco IOS XE Gibraltar 16.10.x or to Cisco IOS XE Gibraltar 16.11.x is not supported. Configure the interface-id snmp-if-index command either during the maintenance window or after isolating the device (by using maintenance mode feature) from the network before doing the ISSU. While performing ISSU from Cisco IOS XE Fuji 16.9.x to Cisco IOS XE Gibraltar 16.12.x, if interface-id snmp-if-index command is not configured with OSPFv3, packet loss can occur. But, there were a few restrictions at the bottom: I was looking up the same thing for Catalyst 9500s and found a section on doing it on stacks in the release notes for 16.12.X.
#Cisco ios xe fuji 16.7.1 installation software#
ISSU does work on certain stacks, with caveats around hardware platforms and software revisions used. Once this operation completes you’ll get prompted to reboot the switch stack.
#Cisco ios xe fuji 16.7.1 installation install#
Next we’ll use install activate to unpack the bin files and add them to the boot config. In this case there was only one additional switch, switch 2. Install add takes the file and copies it to bootflash on all of the switches in the switch stack. Info: Finished copying flash:cat9k_iosxe.16.09.03.SPA.bin to the selected switch(es) : Copying flash:cat9k_iosxe.16.09.03.SPA.bin from switch 1 to switch 2 ! The following is output from the command However, in this case we use a command to help us with that – install add file Ĭ9300-STACK#install add file flash:cat9k_iosxe.16.09.03.SPA.bin Now traditionally you’d have to copy the bin files over to all of the switches in the stack. You’ll be prompted to enter in the IP Address of your TFTP server – which could simply be your laptop running tftpd.Ĭopy tftp flash:cat9k_iosxe.16.09.03.SPA.bin Sync the file to all the Switches in the Stack In this case I installing IOS-XE Fuji 16.9.3. Copy the file to the switch stack using copy tftp bootflash. By default when you’re working with a switch stack you’re working on the stack master.
#Cisco ios xe fuji 16.7.1 installation upgrade#
Copy the new IOS file overĪs with any other IOS upgrade you have to get the files onto the switch stack. I believe there are some newer commands in IOS-XE that help facilitate and make the process a little easier than in previous versions of IOS.
![cisco ios xe fuji 16.7.1 installation cisco ios xe fuji 16.7.1 installation](https://www.netone.co.jp/knowledge-center/netone-blog/files/velo_ipsec_topology_01.PNG_1.png)
The process is very similar to stacking other switches, if you’re familiar with stacking Cisco switches. I recently had to put together a Catalyst 9300 stack of switches and upgrade the switch stack, so I thought I’d document the process and share it. Upgrading IOS-XE on Catalyst 9000 series Switch Stack A pair Cisco Catalyst 9324’s.